Parts List

This page is the host page for parts lists for all my flying *copters. Use links above or to the right to navigate.

Bixler parts

Here is the part list for my HK Bixler build Hobbyking Bixler EPO 1400mm – (ARF) Starting with the motor D2826-6 2200kv Outrunner Motor ESC Hobbyking SS Series 35-40A ESC Servos HXT900 9g / 1.6kg / .12sec Micro Servo Replacement control horns (stocks are not good) Control Horns 16x20mm (10pcs) (requires screws below) Self-Tapping Screws …

View page »

FPV Gear

Here is all FPV gear I use listed. Part List: Skywalker A 1/3 Sony CCD camera is mounted on a XL pan/tilt from Hobbyking EagleTree Logger (v3), GPS, OSD Pro is all connected and it all ends up with a 800mW 1.2Ghz module and a DIY clover leaf antenna made from MIG wire. The Eagletree …

View page »

Hexacopter parts

Here I list my parts used for a more stable Hexacopter. Part list might change… Part List: Arduino pro mini Wiimote plus (WM+) (genuine) Nunchuck (NK) (genuine) optional sensor and connectors: BMP085 altimeter ADXL345(instead of NK) LLC (logic level converter)- needed to connect some sensors or add even more. 6 Motors: hacker Style Brushless Outrunner …

View page »

Quadcopter I parts

Here I list my parts used for a small lightweight Quadcopter. Part list might change… So far I have: Arduino pro mini Wiimote plus (WMP) Nunchuck (NCK) 4 Motors: TURNIGY 2204-14T 19g Outrunner 4 Propellers: GWS 8*4.3 propellers (all CV rotating) 2 tilted motors 4ESC’s: TURNIGY Plush 6A /.8bec/6g Speed Controller Spektrum AR6100 RX Frame …

View page »

Quadcopter II parts

Here I list my parts used for a small but stronger Quadcopter. Part list might change… So far I have: Arduino pro mini Wiimote plus (WM+) (genuine) Nunchuck (NK) (genuine) 4 Motors: hacker Style Brushless Outrunner 20-22L 4 Propellers: ET-ROTORS 2X LEFT, 2X RIGHT (208000) 4ESC’s: TURNIGY Plush 18amp Speed Controller Spektrum AR6100 RX The …

View page »

Quadcopter mk IV

I finished Quadcopter mk IV. It has the exact same components as Quadcopter mk III. There are a few differences: I now used Flyduino base plates instead of my own fabricated from sheet aluminum. The Flyduino base plates are very good and has excellent quality and performance. One thing I had to change was the …

View page »

Skywalker parts

As I purchased a Skywalker from Fpvflying I think it is appropriate to write something about this as well. There is a huge thread with endless resources at RCGroups.com My intentions with this aeroplane is to complement Tricopters/Quadcopters for aerial photo and FPV-flying. It is a stable platform with a pushing propeller so you get …

View page »

T-copter parts

Here I list my parts used for a small T-copter. Part list might change… So far I have: Arduino pro mini Wiimote plus (WMP) Nunchuck (NCK) 3 Motors: TR 35-30C 1100kv Brushless Outrunner (Eq AXi 2808) 3 ESC’s: TURNIGY Plush 30amp Speed Controller Propellers:(many) TP Slow Fly propeller 1047 (10×4.7) GWS style 1 Receiver: Spektrum …

View page »

Tricopter parts

The Tricopter is a regular GYRO-based Tricopter but can easily be converted into a MultiWii if that is what you want. (if you go for MultiWii – exclude all gyros and add Arduino+sensors) Here is the part list for my tricopter so far (might be updated) and the new items are linked 3 Motors: TR …

View page »

Leave a Reply